The Realm of the Verbal Processor

Jarvis's Ramblings

No Assigned Task Sequence

I’ve been setting up a virtual ConfigMgr environment on my laptop to use both for demonstrating at client locations as well as to use for the demo portions of my presentations at MMS and TechEd. It’s running inside Virtual PC 2007, and the server VM is running Windows Server 2008 and ConfigMgr 2007 SP1 R2. It actually runs pretty peppy…I do have the VM running on an external 7200 RPM hard drive connected to my laptop via an eSATA cable.

Anyway…I set up a Task Sequence to do my OS build and capture. It worked fine. Then I imported that WIM file and set up another Task Sequence to deploy that image. It was advertised to both the “All Unknown Computers” collection as well as a special OSD Deploy collection that I had created and imported the name and MAC address of the new VM into.

After booting the new VM with the Bootable Task Sequence media CD, it kept giving me this error message: “Failed to Run Task Sequence” “There are no task sequences available for this computer.” If I looked in the smsts.log file located at “X:\windows\temp\smsts”, I saw an error entry stating: “No assigned task sequence.” Looking through the log file, I could see that it was reading the correct MAC address and had the right SMS GUID that was assigned to the system that I imported. So it was clearly recognizing the machine. It was talking to ConfigMgr correctly. It was downloading policy, but it was determining that none of those policies were applicable. If I looked at the properties of either the Collection or the system, it showed that the advertisement for the Task Sequence was applicable to that computer. So…why would it show as applicable in the GUI, but not be evaluated as applicable during the task sequence?

After beating on this for entirely too long, I finally figured it out this afternoon. I had done a housekeeping task on my VM to move all of the default “All…” collections off of the root of the Collections node (see this post). After doing so, I had forgotten to update those collections after “moving” them. Shouldn’t matter…except that the “All Unknown Computers” collection was completely empty…including not having the “x86 Unknown Computer (x86 Unknown Computer)” or “x64 Unknown Computer (x64 Unknown Computer)” entries.

When the new VM was evaluating policy, it went through the following steps in the SMSTS.log.

Client Identity: GUID:24e41bb6-2d68-451a-9802-29f9f1bdd1ea
Netbios name: NewComputer
Client GUID = GUID:24e41bb6-2d68-451a-9802-29f9f1bdd1ea, Netbios name = NewComputer, State = Unknown
Client is unprovisioned
Using unknown machine GUID: 1b554c94-8eeb-490a-8b10-ae10bd579d3d
Unknown client identity: GUID:24e41bb6-2d68-451a-9802-29f9f1bdd1ea
Preparing Policy Assignment Request.
    Setting transport.
    Setting site code = CM1.
    Setting client ID = 1b554c94-8eeb-490a-8b10-ae10bd579d3d.
Executing Policy Assignment Request.

Note what happens to the GUID. It starts off with the GUID that starts with “24e41…” and a state of “Unknown”. It then switches the GUID that it is going to use for the rest of the process to the “unknown machine GUID” which on my system starts with “1b554…”…this is the GUID for the “x86 Unknown Computer (x86 Unknown Computer)” resource that should be in the “All Unknown Computers” collection. After switching the GUID, you see the last line that I pasted in above where it is “Executing Policy Assignment Request.”

Because I had not updated the collection…and the “x86 Unknown Computer (x86 Unknown Computer)” resource didn’t exist in any collection…there wasn’t any advertisement that was applicable to that GUID. It behaved exactly like it should have. It just took me a long long time to figure out why it was failing. Once I updated the collection, the “problem” went away.

In this instance, it was definitely a PEBKAC issue…Problem Exists Between Keyboard And Chair.

Advertisements

March 20, 2009 - Posted by | ConfigMgr, Microsoft, MMS, TechEd

4 Comments »

  1. Wow, we ran into this same issue!

    Comment by Andy | July 13, 2010

  2. Hi, I understand what you have done. But this does not explain why some machines I can build using the CD media. Especially new laptop Dell E5410. intermittently I get “No Assigned Task Sequence”.
    Any ideas?

    Comment by Carlo | February 21, 2011

  3. Ran into somewhat the same issue, and after reading this post – my SCCM environment is running again!
    Thank you very much!

    Comment by Fabian | April 26, 2011

  4. It works for me too. Thanks

    Comment by Tom | April 11, 2012


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s